Скачать FPGA проекты, документацию или драйвера


Микросхемы и компоненты

RGB LED with integrated controller

WS2812B is a intelligent control LED light source that the control circuit and RGB chip are integrated in a package of 5050 components. It internal include intelligent digital port data latch and signal reshaping ampli fication drive circuit. Also include a precision internal oscillator and a 12V voltage programmable constant curr e-nt control part, effectively ensuring the pixel point light color height consistent.


Описание приемопередатчика Ethernet 10/100Mb Realtek RTL8201BL

Micron 64Mbit SDRAM 4x1Mx16bit

MT48LC8M8A2 – 2 Meg x 8 x 4 Banks
MT48LC4M16A2 – 1 Meg x 16 x 4 Banks

The 64Mb SDRAM is a high-speed CMOS, dynamic random-access memory containing 67,108,864 bits. It is internally configured as a quad-bank DRAM with a synchronous interface (all signals are registered on the positive edge of the clock signal, CLK). Each of the x8’s 16,777,216-bit banks is organized as 4096 rows by 512 columns by 8 bits. Each of the x16’s 16,777,216-bit banks is organized as 4096 rows by 256 columns by 16 bits.

• PC100- and PC133-compliant
• Fully synchronous; all signals registered on positive
edge of system clock
• Internal, pipelined operation; column address can
be changed every clock cycle
• Internal banks for hiding row access/precharge
• Programmable burst lengths: 1, 2, 4, 8, or full page
• Auto precharge, includes concurrent auto precharge
and auto refresh modes
• Self refresh mode (not available on AAT devices)
• Refresh
– 64ms, 4096-cycle refresh (15.6?s/row)
– 16ms, 4096-cycle refresh (3.9?s/row)
• LVTTL-compatible inputs and outputs
• Single 3.3V ±0.3V power supply
• AEC-Q100
• PPAP submission
• 8D response time

64Mbit SDRAM 1M x 16Bit x 4 Banks Synchronous DRAM

Описание микросхемы SDRAM.

The K4S641632F is 67,108,864 bits synchronous high data rate Dynamic RAM organized as 4 x 1,048,576 words by 16 bits, fabricated with SAMSUNG?s high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the same
device to be useful for a variety of high bandwidth, high performance memory system applications.

• JEDEC standard 3.3V power supply
• LVTTL compatible with multiplexed address
• Four banks operation
• MRS cycle with address key programs
-. CAS latency (2 & 3)
-. Burst length (1, 2, 4, 8 & Full page)
-. Burst type (Sequential & Interleave)
• All inputs are sampled at the positive going edge of the system clock
• Burst read single-bit write operation
• DQM for masking
• Auto & self refresh
• 64ms refresh period (4K cycle)

Altera Cyclone III Device Handbook

Описание микросхем FPGA семейства Cyclone III компании Altera

The Cyclone® III device family offered by Altera® is a cost-optimized, memory-rich FPGA family. Cyclone III FPGAs are built on Taiwan Semiconductor Manufacturing Company (TSMC)’s 65-nm low-power (LP) process technology with additional silicon optimizations and software features to minimize power consumption. With this third-generation in the Cyclone series, Altera broadens the number of high volume,
cost-sensitive applications that can benefit from FPGAs.


ADC1175 8-Bit, 20MHz, A/D Converter

Аналогово-цифровой преобразователь. 8 бит, 20Мгц.

The ADC1175 is a low power, 20 Msps analog-to-digital converter
that digitizes signals to 8 bits while consuming just 60
mW of power (typ). The ADC1175 uses a unique architecture
that achieves 7.5 Effective Bits. Output formatting is straight
binary coding.
The excellent DC and AC characteristics of this device, together
with its low power consumption and +5V single supply
operation, make it ideally suited for many video, imaging and
communications applications, including use in portable
equipment. Furthermore, the ADC1175 is resistant to latchup
and the outputs are short-circuit proof. The top and bottom of
the ADC1175’s reference ladder is available for connections,
enabling a wide range of input possibilities.

42S16800B Synchronous DRAM

Описание микросхем динамической памяти 

IS42S81600B, IS42S16800B
16Meg x 8, 8Meg x16

Integrated Silicon Solution, Inc. — www.issi.com


Цветная активная матрица LCD, выполненная в виде TFT панели с контроллером и системой освещения.

B121EW03 V6 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a driver circuit, and backlight system. The screen format is intended to support the WXGA (1280(H) x 800(V)) screen and 262k colors (RGB 6-bits data driver) without backlight inverter.

All input signals are LVDS interface compatible.

AT45DB041D - Atmel Data Flash

Описание микросхем флеш памяти Atmel: 4-megabit, 2.5-volt or 2.7-volt DataFlash® AT45DB041D

The AT45DB041D is a 2.5V or 2.7V, serial-interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applications.

The AT45DB041D supports RapidS serial interface for applications requiring very high speed operations. RapidS serial interface is SPI compatible for frequencies up to 66 MHz. Its 4,325,376 bits of memory are organized as 2,048 pages of 256 bytes or 264 bytes each. In addition to the main memory, the AT45DB041D also contains two SRAM buffers of 256/264 bytes each. The buffers allow the receiving of data while a
page in the main Memory is being reprogrammed, as well as writing a continuous data stream. EEPROM emulation (bit or byte alterability) is easily handled with a self-contained three step read-modify-write operation. Unlike conventional Flash memories that are accessed randomly with multiple address lines and a parallel interface, the DataFlash uses a RapidS serial interface to sequentially access its data. The simple
sequential access dramatically reduces active pin count, facilitates hardware layout,increases system reliability, minimizes switching noise, and reduces package size. The device is optimized for use in many commercial and industrial applications where high-density, low-pin count, low-voltage and low-power are essential.

To allow for simple in-system reprogrammability, the AT45DB041D does not require high input voltages for programming. The device operates from a single power supply, 2.5V to 3.6V or 2.7V to 3.6V, for both the program and read operations. The AT45DB041D is enabled through the chip select pin (CS) and accessed via a three-wire interface consisting of the Serial Input (SI),Serial Output (SO), and the Serial Clock (SCK).

All programming and erase cycles are self-timed.


Спецификация LCD дисплея

Innolux LCD display module specification

Мы подключаем этот дисплей к плате Марсоход.

Model Name: AT070TN83 V.1

1 LCD size 7.0 inch(Diagonal)
2 Driver element a-Si TFT active matrix
3 Resolution 800X3(RGB)X480
4 Display mode Normally white, Transmissive
5 Dot pitch 0.0635(W)X0.1905(H) mm
6 Active area 152.4 (W)X91.44 (H) mm
7 Module size 165(W)X104(H)X5.5(D) mm Note 1
8 Surface treatment Anti-Glare
9 Color arrangement RGB-stripe
10 Interface Digital(TTL)
11 Backlight power consumption 2.500W(Typ.) Note 3
12 Panel power consumption 0.825W(Typ.) Note 2
13 Weight 130g (Typ.)


VGA камера, модуль Toshiba

Описание модуля VGA камеры TOSHIBA, использовалась в сотовых телефонах. 

Schottky barrier rectifier: 1N5817 - 1N5819
BC817 NPN general purpose transistor

Voltage regulator diodes BZV55 series

· Total power dissipation: max. 500 mW
· Two tolerance series: ±2%, and approx. ±5%
· Working voltage range: nom. 2.4 to 75 V (E24 range)
· Non-repetitive peak reverse power dissipation: max. 40 W.
· Low voltage stabilizers or voltage references.
Low-power voltage regulator diodes in small hermetically sealed glass SOD80C SMD packages. The diodes are available in the normalized E24 ±2% (BZV55-B) and approx. ±5% (BZV55-C) tolerance range. The series
consists of 37 types with nominal working voltages from 2.4 to 75 V.

Ультразвуковой дальномер HC-SR04

Описание на HC-SR04

Ultrasonic ranging module : HC-SR04
power supply :5V DC
quiescent current : <2mA
effectual angle: <15°
ranging distance : 2cm – 500 cm
resolution : 0.3 cm

A short ultrasonic pulse is transmitted at the time 0, reflected by an object. The senor receives this signal and converts it to an electric signal. The next pulse can be transmitted when the echo is faded away. This time period is called cycle period. The recommend cycle period should be no less than 50ms. If a 10?s width trigger pulse is sent to the signal pin, the Ultrasonic module will output eight 40kHz ultrasonic signal and detect the echo back. The measured distance is proportional to the echo pulse width and can be calculated by the formula above. If no obstacle is detected, the output pin will give a 38ms high level signal.

Стабилизатор напряжения LM1117

Описание стабилизатора напряжения LM1117 (National Semiconductor)

LM1117 / LM1117I 800mA Low-Dropout Linear Regulator
General Description

The LM1117 is a series of low dropout voltage regulators with a dropout of 1.2V at 800mA of load current. It has the same pin-out as National Semiconductor’s industry standard LM317.

The LM1117 is available in an adjustable version, which can set the output voltage from 1.25V to 13.8V with only two external resistors. In addition, it is also available in five fixed voltages, 1.8V, 2.5V, 2.85V, 3.3V, and 5V.

The LM1117 offers current limiting and thermal shutdown. Its circuit includes a zener trimmed bandgap reference to assure output voltage accuracy to within ±1%.

The LM1117 series is available in LLP, TO-263, SOT-223, TO-220, and TO-252 D-PAK packages. A minimum of 10?F tantalum capacitor is required at the output to improve the transient response and stability.

Модуль Bluetooth

Техническая документация на модуль Bluetooth компании National Semiconductor LMX9838

LMX9838 Bluetooth® Serial Port Module
1.0 General Description
The National Semiconductor LMX9838 Bluetooth Serial Port module is a fully integrated Bluetooth 2.0 baseband controller, 2.4 GHz radio, crystal, antenna, LDO and discreets; combined to form a complete small form factor (10 mm x 17 mm x 2.0 mm) Bluetooth node.

All hardware and firmware is included to provide a complete solution from antenna through the complete lower and upper layers of the Bluetooth stack, up to the application including the Generic Access Profile (GAP), the Service Discovery Application Profile (SDAP), and the Serial Port Profile (SPP).

The module includes a configurable service database to fulfil service requests for additional profiles on the host. Moreover, the LMX9838 is qualified as a Bluetooth endproduct, ready to be used in the end application without additional testing and license cost.

Based on National’s CompactRISC® 16-bit processor architecture and Digital Smart Radio technology, the LMX9838 is optimized to handle the data and link management processing requirements of a Bluetooth node.
The firmware supplied in the on-chip ROM memory offers a complete Bluetooth (v2.0) stack including profiles and command interface. This firmware features point-to-point and point-to-multipoint link management supporting data rates up to the theoretical maximum over RFComm of 704 kbps. The internal memory supports up to 7 active Bluetooth data links and one active SCO link.

The on-chip Patch RAM provided for lowest cost and risk, allows the flexibility of firmware upgrade.
The module is lead free and RoHS (Restriction of Hazardous Substances) compliant.
2.0 Features
? Complete Bluetooth 2.0 Stack including
— Baseband and Link Manager
— Protocols: L2CAP, RFCOMM, SDP
— Profiles: GAP, SDAP, SPP
? High Integration: Includes Antenna, crystal, EEPROM, LDO
? Supporting up to 7 active Bluetooth data links and 1 active SCO link
? Class 2 operation
? UART Command/Data port speed up to 921.6kbits/s
? Advanced Audio Interface for external PCM codec
? Better than -80dBm input sensitivity
? FCC certified: FCC ID: ED9LMX9838
? IC certified: IC-1520A-LMX9838
? CE Self certified
? Bluetooth SIG QD ID: B012394
? Compact Size: 10mm x 17mm x 2.0mm

LCD дисплей

Описание на LCD дисплей Winstar WH0802A-YGH-CT

GPS приемник

Описание на GPS приемник CONDOR

The Condor™+ GPS receiver is part of the Trimble® family of value-optimized GPS modules. The Condor family includes modules of different form factors and feature sets, allowing you, the system designer, to choose the optimal module solution for your particular application.

All the Condor GPS modules offer top-tier accuracy, sensitivity, and acquisition performance. Whether you
are designing a handheld device or a complex fleet management system, Trimble offers a Condor module for
optimal system design, cost, and performance:
• The smallest Condor module at 10 x 11 mm.
• At 19 x 19 mm, similar in form factor to the Trimble Copernicus® family of richly featured GPS modules. Two more modules will be added to the Condor family in Q2/2009. Contact Trimble or a Trimble representative to learn more about the current and future modules in the Condor family and to obtain a Condor evaluation kit.

Condor+ is a complete, autonomous GPS receiver module that requires a minimum of external components.


Преобразователь уровней для RS232

+5V Powered RS-232 Transmitters/Receivers with 0.1Microfarad External Capacitors The HIN202-HIN213 family of RS-232 transmitters/receivers interface circuits meet all ElA RS-232E and V.28 specifications, and are particularly suited for those applications where ±12V is not available. They require a single +5V power supply and feature onboard charge pump voltage converters which generate +10V and -10V supplies from the 5V supply The family of devices offers a wide variety of RS-232 transmitter/receiver combinations to
accommodate various applications (see Selection Table).

The HIN206, HIN211 and HIN213 feature a low power shutdown mode to conserve energy in battery powered
applications. In addition, the HIN213 provides two active receivers in shutdown mode allowing for easy “wakeup” capability.

The drivers feature true TTL/CMOS input compatibility, slew rate-limited output, and 300? power-off source impedance. The receivers can handle up to ±30V input, and have a 3k? to 7k? input impedance. The receivers also feature hysteresis to greatly improve noise rejection.

• Any System Requiring RS-232 Communications Port
- Computer - Portable, Mainframe, Laptop
- Peripheral - Printers and Terminals
- Instrumentation
- Modems

Warning: count(): Parameter must be an array or an object that implements Countable in /home/nkovach/domains/marsohod.org/public_html/components/com_phocadownload/views/category/tmpl/default.php on line 105
Powered by Phoca Download